|
Nixalite® Climbing barriers on
Round Objects
These guidelines provide the basic steps for installing a climbing animal barrier on a vertical
round pole. If you have a square object,
go to Nixalite Climbing Barriers on
Square Objects.
These steps are for a typical installation - your application may be
different and may require different or additional steps. If you have
any questions, Contact Nixalite.
For a hardcopy of these instructions download
Climbing Barrier on
Round Objects. (PDF)
Installing on Round Objects:
NOTE: Do not use Soft Tip (flat wire tip) Nixalite models for
climbing animal barriers.
Where to start. Always begin the barrier installation at
the top where the pole ends or where it meets the object it supports
(example; a bird house, the ceiling, the bottom of a overhang).
Do You Have Enough Space?
A typical six row climbing barrier takes up about 2-1/2 ft (76 cm).
We recommend that the bottom row is at least 5 ft (152 cm) off the
ground. So, you should have 7-1/2 ft (228 cm) of uninterrupted,
vertical space to install the ideal climbing barrier. If not,
Contact Nixalite
for alternatives.
Accurately measure and record the diameter of the pole (the width
of the pole).
If you know the circumference (distance around the outside) and need
the diameter, divide the circumference by 3.14 (π).
 |
At the top of the pole, measure
down 2-1/8 inches (5.4 cm)
and draw a level line around the outside of the pole (the circumference). |
 |
From the line just drawn, measure down 4-1/2 inches (11.4
cm) and draw another line around the outside of the pole.
Repeat this step 4 more times until you have 6
individual lines spaced 4-1/2 inches (11.4 cm) apart. |
Use the hardware spacing information below to find the
quantity and spacing of mounting hardware needed for the pole
diameter.
To find the hardware that best suits your application, go to the
Mounting Hardware page.
Mounting Hardware for Diameter Table
The
quantity mounting hardware depends on the diameter of the pole.
| Diameter inches (cm) |
|
Hardware |
| 1-1/2” – 3" (3.8 – 7.6 cm) |
|
3 units of hardware + 1 additional clip |
| 3” – 5" (7.6 – 12.7 cm) |
|
4 units of hardware + 1 additional clip |
| 5" – 7” (12.7 – 17.8 cm) |
|
5 units of hardware + 1 additional clip |
| 7” – 9” (17.8 – 22.8 cm) |
|
6 units of hardware + 1 additional clip |
| 9” – 11” (22.8 – 28.0 cm) |
|
7 units of hardware + 1 additional clip |
| 11” – 13” (28.0 – 33.0 cm) |
|
8 units of hardware + 1 additional clip |
| 13” – 15” (33.0 – 38.1 cm) |
|
9 units of hardware + 1 additional clip |
1 mounting clip is added to the hardware totals for the double
clip application.
1-1/2” diameter is the minimum diameter for this method.
15” is the maximum diameter for a single 4 foot strip.
 |
At each line, mark the mounting hardware locations, spacing them equally around the
outside of the pole. Install the clip with the
hook end pointing towards the ground.
NOTE: one hardware location will have 2 CLIPS to fasten both ends of the same Nixalite
strip.
That is the reason for the additional clip noted in the chart.
Tip: to help
prevent gaps, move the double clip location about 30 degrees
from row to row (so it doesn't line up from one row to the
next). |
 |
Before installing the Nixalite strip, make sure it will go around the circumference of the pole,
beginning and ending at the double clip hardware. Cut the Nixalite strip to fit (if needed)
and pull the Nixalite base strip down into the hook of the
mounting clips. Repeat for each row. |
 |
The top row of Model W Nixalite is installed with the 6 wire side facing up, toward the top of the pole. The
bottom row of Model W Nixalite
is installed with the 6 wire side facing down towards the
ground. |
Where to go from here..
For climbing barriers on square objects,
go to Climbing Barriers on
Square Objects.
For climbing barrier on special applications, go to
Climbing Barriers for
Special Applications.
Back To Top
|
